Partner for mineral-insulated thermocouple cables, measurement cables & heating cables

ISOMIL stands for quality you can trust. Close collaboration with leading customers worldwide guarantees a wide range of products with maximum flexibility and the highest reliability. We are both manufacturer and service provider and offer our national and international customers everything from a single source: from professional consulting to customised solutions. Our knowledge is based on our wealth of experience built up over the last few decades. Our headquarters is centrally located in Germany – in the city of Hanau am Main.


Versatile application areas


Products

Find a selection of our state-of-the-art products here:

ISOMIL-T

ISOMIL-T

ISOMIL-M

ISOMIL-M

ISOMIL-H

ISOMIL-H

Customised solution

Customised solution


ISOMIL-T - Thermocouple cable

ISOMIL-T

In ISOMIL-T, the thermoelectric voltages of the thermocouples correspond to the basic values within the usual tolerance range. For NiCr-Ni, the basic values of thermoelectric voltage are identical in German and international standards. For both Fe-CuNi (thermo-iron thermo-constantan) and Cu-CuNi (thermo-copper thermo-constantan), they differ.

The tolerance value of the thermoelectric voltage is available in accordance with the following standards:

  • DIN IEC 584-2
  • ASTM E 230-93
  • DIN 43710 – standard was withdrawn

The cables are manufactured in accordance with the DIN EN 61515 standard:

To the product specification of ISOLMIL-T


ISOMIL-M - Measurement cable

ISOMIL-M

The inner conductor is usually a low-impedance wire (in some cases several wires) which transmits the electrical signal. Conductors of this kind are used in measurement and control technology and are therefore referred to as sheathed measuring conductors.

To the product specification of ISOMIL-M


ISOMIL-H - Heating cable

ISOMIL-H

The inner conductor is a heating wire made of suitable material and with the corresponding dimensions for electrical resistance heating operation. This combination is referred to as a sheathed heating conductor.

To the product specification of the 300 V MI heating cable

To the product specification of the 400 V MI heating cable

To the product specification of the 600 V MI heating cable

To the product specification of the 800 V MI heating cable


Customised solution

Schliffbild_von_Sonderloesungen

For special designs such as coaxial cables, double-walled cables, cables with offset inner conductors, we require the following information:

  • Technical drawing (if available)
  • Dimensions with tolerance specifications
  • Material specifications
  • If applicable, resistance of the inner conductors / heating conductors

Please note that for customised solutions, a complete cable length must be accepted.

We will check your request immediately.


Product-related environmental protection

ISOMIL GmbH has established a comprehensive management system to ensure compliance with product-related environmental protection issues. Below are explanations of the most common topics.

1. Regulation (EC) No. 1907/2006 (REACH)

In accordance with Art. 33 of the REACH regulation, ISOMIL GmbH is obliged to inform their customers, if one of their products contain a substance of very high concern in a concentration of more than 0.1 percent.

The list of the SVHC substances can be found on the Internet pages of the European Chemicals Agency (ECHA) under http://echa.europa.eu.

Up to today, we are not aware that products from ISOMIL, delivered to you contain any SVHC substances in concentrations over 0.1% by weight. If any SVHC substance is present in our products at the mass concentration mentioned, we would inform you immediatly.

2. EU directive RoHS (2011/65/EU, 2015/863/EU)

Temperature cables sold by ISOMIL GmbH fulfill the requierements of the EU directive (EU) 2011/65 with the regard to the following substances.

Lead (Pd) - 0,1% / Mercury (HG) - 0,1% / Hexavalent chromium (CrVI) - 0,1% / Cadmium (Cd) - 0,01% / Polyprominated biphenyls (PBB) - 0,1% / Polyprominated diphenyl ethers (PBDE) - 0,1%

We also confirm compliance of our products regarding the list of substances on (EU) 2015/863:

Di(2-ethylhexyl)phthalat (DEHP) - 0,1% / Butylbenzylphthalat (BBP) - 0,1% / Dibutylphthalat (DBP) - 0,1% / Diisobutylphthalat (DIBP) - 0,1%

3. Conflict minerals

The enactment of section 1502 of the US American Dodd-Frank Act commits listed US companies to provide proofs of origin for the raw materials tantalum, gold, tungsten, and tin and furthermore to put far-reaching auditing requirements for suppliers and material flows into practice. The objective is to reveal the global supply chains in order to ensure that no conflict commodities are contained in end products.

Such a product-specific disclosure and supply chain protection of the entire product portfolio of ISOMIL from commodities to the end product, i.e. a certification of each manufacturing step, is not reliably feasible. Furthermore, the certificates which were created with a great deal of erffort cannot be verified. In this connection, ISOMIL supports the demands of the ZVEI to exclusively conduct a certficiation of melting facilities.

Our sources of supply consist of qualified and well-known suppliers, without exception.

ISOMIL has already obtained confirmations from its major suppliers. To the present day, these suplliers certify without exception that no raw materials originating from such countries, which are listed in the already mentioned US American Dodd-Frank Act, are used. These certify to this day, without exception, that no raw materials from such countries that are mentioned in the cited US-American Dodd-Frank Act are used.

Due to the reasons mentioned above, ISOMIL cannot make a general statemant or fill our customer-specific questionnaires.


Downloads

Download the information directly as a PDF:

Here you will find all the important brochures with information on our products and specifications. If you have any further questions, please do not hesitate to contact us directly.

Certificate DIN EN ISO 9001:2015

General terms and conditions


Contact

How can we help you?

Contact us to clarify any questions you may have or to share your opinion with us – we are always available for you:

ISOMIL GmbH
Ehrichstraße 10
D-63450 Hanau
Tel.: +49 (0) 6181 931550
E-mail: info@isomil.de